NEW

Bedec Multi Surface Paint

£11.90 – £53.80 inc VAT

250ml
750ml
2.5 Litre

Colour

Anthracite
Dark Grey
Gold
Holly
Inca
Magnolia
Oxford Blue
Red Cossack
Silver
Soft White
Black

Finish

Gloss
Satin
Matt

Clear

Enter colour code wantedPlease enter the colour code you want, this could be from a colour Crown, Macpherson, Sandtex or Sadolin chart or any British Standard NCS or RAL chart, please state clearly what code and where you are getting it. If you have had this colour before from a ready-mixed tin it may not match exactly. And as always colour charts are only a guide they are never 100% accurate so you may want to order a sample pot first to see if it is right for you. Sample pots are only available in Crown Vinyl Matt. We will always contact you first to confirm before mixing and shipping your bespoke colour. For Black or Magnolia (BS 4800 code 08B15), please write Black or Magnolia.

SKU: N/A Categories: Gloss, Matt, Paints, Satin

Description
Additional information

Product Description

Bedec Multi Surface Paint is a paint for use both inside and outside with a built in universal primer.
A proven water-based paint that resists flaking or peeling due to it’s outstanding flexibility. Easy to apply directly onto almost anything, including (but not limited to) plastic, wood, metal, cladding, brick, UPVC, MDF, and tiles! As it is a water-based product it all but eliminates yellowing with age, and it makes it very convenient to clean up using water.
Choose from a range of colours in Matt, Satin and Gloss finishes. If you cannot see the colour or size you require please send us an email. Please note certain colours are only available in some finishes and sizes.

Surface preparation

Ensure the surfaces to be painted are clean, dry and free from dust, dirt, grease and wax
Remove all loose and defective paint
Remove and treat any Algal, mould and fungal growths with a fungicidal wash. Smooth glossy surfaces should be lightly abraded to provide a key
For specific surface preparation instructions please refer to the data sheet below

Directions for use

Stir well and check colour before use in case any of the product has settled in the tin.
Apply with a brush, roller, conventional H.V.L.P or airless spray
Do not apply at air or surface temperatures below 8°C, when likely to rain before the paint has fully dried or above 30°C as this may cause uneven drying.
Apply two to three coats to sealed surfaces allowing each coat to dry thoroughly
Do not over spread
Recoatable after approximately 4 hours

Tips for use

Be mindful that spraying can reduce the coverage rate depending on the type of spray equipment you are using
Clean up immediately after use with warm soapy water. Ensure when using a roller sleeve that it is washed out thoroughly and left slightly damp before use, to remove loose fibres, dust and to create a liquid barrier between the paint and the roller to avoid the paint absorbing into the roller.

Key Benefits

Resists flaking and cracking
Chalks much less
No special thinners required
Low VOC
Alkali resistant
Heat resistant up to 80 Degrees Celsius

Technical Information

Bedec Multi Surface Technical Data Sheet

Weight	N/A
Size	250ml, 750ml, 2.5 Litre
Colour	Anthracite, Dark Grey, Gold, Holly, Inca, Light Grey, Magnolia, Oxford Blue, Red Cossack, Silver, Soft White, Black
Finish	Gloss, Satin, Matt
Coverage per litre	12 – 14 Square metres
Suitable surfaces	Aluminium, Brick, Cladding, Copper, Fibreglass, Galvanised steel, MDF, Metal (including radiators), Much more, please refer to the data sheet for more information, Plaster, Plastic, Plastic coated steel, Plastics, Stone, terracotta, UPVC, Masonry, Melamine, Wood
Touch dry	2 hours
Overcoat time	4 Hours
Use for interior or exterior	Both (exceptions apply)
Thinner	Water